image_not_found

HEDP in Water Treatment: Selection and Dosing Guide

Phosphonates have been leaving water treatment programmes across northern Europe for a decade, and the direction of travel is clear. Yet plants still buy HEDP in quantity, and the reasons are technical rather than sentimental: at high temperature, high hardness and high cycles of concentration, a phosphonate still does a job that a polymer alone struggles with. The useful question is not whether HEDP belongs in a programme, but where it earns its place and how to run it without breaching a phosphorus limit.

What HEDP is, in plant terms

HEDP is 1-hydroxyethylidene-1,1-diphosphonic acid, known also as etidronic acid, supplied either as the acid, as its sodium salts, or as a concentrated aqueous solution. It carries two phosphonic acid groups on a single carbon, which gives it a compact, strongly adsorbing structure rather than a long chain.

Three properties follow from that structure and explain most of its uses. It binds divalent and trivalent metal ions firmly across a wide pH range. It adsorbs on crystal surfaces at doses far below the stoichiometric ratio, so a few milligrams per litre can hold a large mass of calcium carbonate in check. And it is hydrolytically stable compared with some other phosphonates, which is why it survives in systems that run hot.

Threshold inhibition and the dose that follows

The dose question confuses buyers more than any other. A chelating agent is dosed against the metal load, roughly mole for mole. A threshold inhibitor is not. It works by adsorbing onto the growing crystal and disturbing the lattice, so a small number of molecules can arrest the growth of a much larger mass of scale.

That is why HEDP appears in programmes at a few milligrams per litre while a chelant appears at hundreds. It is also why overdosing is not a harmless mistake: past the threshold range the extra phosphonate buys very little inhibition and adds directly to the phosphorus load in the blowdown.

The practical dose window in open recirculating cooling water typically sits in the low single figures of milligrams per litre, set against the water's hardness, alkalinity, temperature and cycles of concentration. A plant that changes its cycles without re-checking the dose is running a different programme from the one that was designed.

Where HEDP still holds an advantage

Three situations keep HEDP in the treatment room.

The first is high temperature. Above the range where polymers lose activity, a phosphonate continues to adsorb and inhibit, which matters in boiler feedwater, in hot process cooling and in systems with high surface temperatures.

The second is severe hardness with high cycles of concentration. Where calcium carbonate is heavily supersaturated, the threshold effect of a compact phosphonate gives more margin than a polycarboxylate at the same active dose.

The third is dual function. At higher doses HEDP also acts as a corrosion inhibitor, particularly on carbon steel in the presence of calcium and often with zinc, which means one product addresses two problems in a small system where a multi-component programme is impractical.

Where none of those three applies, a phosphorus-free programme built on a polymer and a biodegradable chelant is usually the better commercial and regulatory choice, and the note on designing a phosphorus-free programme sets out how to make that switch.

The grade question: acid, salt or solution

HEDP is sold in several forms and the differences matter at the dosing tank, not on the specification sheet.

The free acid is a strong acid, corrosive in concentrated form, and it dissolves readily, which makes it convenient for blending but demanding on materials and on operator protection. The sodium salts are easier to handle, more alkaline in solution, and better suited to systems where a pH drop would disturb the programme. The 60 per cent aqueous solution is the form most plants buy: it is pumpable, does not need dissolving, and keeps the dosing system simple.

Two consequences follow. A quotation expressed as a percentage of active content is not comparable with one expressed as a percentage of product, so ask for the basis. And the sodium content of a salt grade adds to the dissolved solids in a system that is already concentrating, which in a high-cycles plant is worth checking before the grade is fixed.

Phosphorus accounting before the first drum

A phosphorus limit is arithmetic, and it is worth doing before the programme is changed rather than after the permit is queried.

The calculation runs from the dose, the phosphorus content of the product, the blowdown volume and the receiving water's consent. A programme dosing 3 milligrams per litre of product into a system with a blowdown of 50 cubic metres a day is releasing a small but measurable mass of phosphorus each day, and the consent is expressed in concentration at the discharge point, not in the cooling tower.

Two practical measures keep the figure in range. Reduce the dose to the threshold that actually works, which usually means measuring rather than assuming, and reduce blowdown where the water chemistry allows, since the same dose at lower blowdown releases less phosphorus for the same cooling duty. Where the local consent is tight, a hybrid programme that uses phosphonate only in the hot part of the circuit, and polymer elsewhere, sometimes gets the answer without abandoning the chemistry that works.

Running the programme: what to monitor

Four measurements tell you whether the programme is doing what it was designed to do.

Calcium hardness in the circulating water, because it defines the supersaturation the inhibitor has to hold. Orthophosphate, because it rises when the phosphonate starts to break down and because it signals the risk of calcium phosphate deposition. Total phosphorus in the blowdown, because that is what the consent is written against. And the scaling or corrosion indicators the plant already tracks, recorded as a trend rather than a spot reading.

The orthophosphate reading deserves emphasis. A rise in a system that has not changed its dose is the earliest sign that something is attacking the molecule, and in a chlorinated system that something is usually the oxidant. The companion note on how chlorine breaks down HEDP explains the mechanism and the practical consequences.

Specifying and buying

A purchase specification for HEDP should pin down the active content and its basis, the pH of the supplied solution, the density, the chloride content if the product will meet stainless steel, and the phosphorus content per unit of product so the discharge calculation can be repeated.

Ask for the certificate of analysis per batch, not only a generic specification, because active content and chloride vary between lots. Ask also for the REACH registration status and the safety data sheet in the language of the market where the product will be used, since HEDP carries a classification that affects storage, transport and operator training.

The product range, including the grades supplied for water treatment, is listed on the HEDP product page.

When to move away from it

A programme should move away from HEDP when the phosphorus consent tightens beyond what the dose can meet, when the circuit is chlorinated continuously and the orthophosphate trend is rising, or when a phosphorus-free alternative has been trialled on the actual water rather than on a competitor's case study.

The move is not always a straight swap. A polymer and chelant combination usually needs higher active dose to match a phosphonate at high temperature, and the corrosion side has to be re-established separately. A trial on a sidestream, run for long enough to see a full scaling cycle, is the only way to know.

Frequently asked questions

Is HEDP a chelating agent or a scale inhibitor? Both, depending on dose. At a few milligrams per litre it works by threshold inhibition. At higher doses it complexes metals and contributes to corrosion control.

Can HEDP replace a chelant in a cleaning programme? Not usually. Cleaning needs stoichiometric metal binding, and HEDP is expensive to use that way. It belongs in the inhibition part of the programme.

Does HEDP contain phosphorus? Yes, two phosphorus atoms per molecule, which is why discharge accounting matters wherever a phosphorus limit applies.

Is it compatible with oxidising biocides? It tolerates intermittent oxidant dosing better than some phosphonates, and degrades under continuous chlorination. Monitor orthophosphate rather than assuming either behaviour.

Which grade should a small plant buy? The 60 per cent solution, in most cases. It needs no dissolving, pumps cleanly and keeps the dosing system simple.

For a programme review, water analysis interpretation or a sample of HEDP in the grade you need, write to [email protected] or call +86-537-3739818. Product data is listed at yuanlianchem.com, with mechanism notes at yuanlianchelating.com.

 

Yuanlian Chemical specializes in the production of polyaspartic acid (PASP),tetrasodium iminodisuccinate(IDS), GLDA, MGDA etc. with stable quality and excellent quantity!

Contact us

verification code
wechat qrcode