Chelating Agents for Geothermal District Heating Systems
A geothermal district heating scheme is a chemical plant that nobody calls a chemical plant. Water arrives at 60 to 90 °C, gives up its heat to a network of hundreds of buildings, and is returned to the ground. Between those two points the fluid changes pressure three or four times, loses dissolved gas, cools, and meets a different alloy at every stage. Almost every scaling and corrosion problem in a geothermal loop can be traced to one of those transitions.
This guide looks at where a chelating agent earns a place in that circuit, where it does not, and what a buyer should put in the tender so that the offers can be compared.
Why geothermal water is not just hot groundwater
Three properties separate geothermal fluid from the groundwater a municipal plant handles.
It is usually saturated or close to saturated with respect to a carbonate or sulphate mineral at reservoir conditions, because it has spent geological time in contact with rock at elevated temperature and carbon dioxide pressure. Bringing it to the surface changes the conditions under which that saturation was established.
It carries gases that were only soluble because of pressure. Carbon dioxide is the important one, and hydrogen sulphide in some fields. Losing those gases at the wellhead changes pH and redox state at the same moment.
It is often saline, sometimes strongly so, and the chloride content decides which alloys are viable. A fluid at 80 °C with 2 per cent chloride is a different materials problem from one at 40 °C with 200 mg/l.
A chelating agent is a tool for the first property. It cannot fix the third, and buying one to solve a chloride corrosion problem is the most common way money is wasted in this sector.
The scaling window opens when pressure drops
Carbon dioxide is what keeps calcium carbonate in solution downhole. As the fluid rises and pressure falls, the gas comes out of solution, pH climbs, and the carbonate equilibrium shifts towards precipitation. The scale does not form because the water got hotter; it forms because the water lost the acid gas that was holding it in balance.
This is why scale in geothermal systems often appears at the wellhead assembly, in the first valve after the expansion point, and on the hot side of the exchanger rather than uniformly through the loop. It is also why the dosing point should be upstream of the first pressure drop that matters, not at the plant boundary where most dosing skids are installed.
A chelating agent dosed upstream holds the calcium as the pH rises, so the fluid arrives at the exchanger below saturation. Dosed downstream, it has to dissolve scale that has already formed, which is a slower and less reliable operation and risks releasing particles into the network.
Four deposits, four different mechanisms
It helps to name the deposit before choosing the chemistry, because a chelant that works on one may be irrelevant to another.
Calcium carbonate is the common case and responds well to a chelant. It forms on pressure drop and on heating in the exchanger, and it is reversible if treated early.
Calcium sulphate behaves in the opposite way to most salts: its solubility falls as temperature rises. That makes the hottest surface in the plant the place it appears, which is usually the exchanger plate, and it makes a hot alkaline clean the wrong choice. Chelants can hold calcium sulphate to some extent, but prevention by temperature management and by dilution is the more reliable route.
Metal sulphides, particularly iron, zinc and lead sulphide, form where sulphidic water meets a metal surface or mixes with an oxygen-bearing stream. They are not removed by ordinary chelation alone, and their presence is usually a signal to look at redox control rather than at the scale programme.
Silica is the one that catches people out in cooling. Amorphous silica polymerises as the fluid cools and can deposit as a hard, glassy layer that no chelant will remove at neutral pH. Once silica has gone past its polymerisation point, the answers are dilution, temperature control and preventing the cooling in the first place. This is worth saying plainly, because silica is often sold as a chelant application when it is not.
Corrosion in a closed loop with carbon dioxide and chloride
The corrosion question in a geothermal loop has three drivers, and only one of them is under the chemical programme's control.
Dissolved carbon dioxide gives carbonic acid and a pH in the range where carbon steel corrodes uniformly. Hydrogen sulphide adds sulphide stress cracking risk on high-strength steels. Chloride sets the pitting risk and rules out the cheaper stainless grades above quite modest concentrations.
A chelating agent is not a corrosion inhibitor. What it does is remove the conditions that make inhibition difficult: it keeps iron in solution so that it does not deposit as a porous hydroxide that harbours under-deposit corrosion, and it prevents the calcium carbonate film that can mask a developing pit until it perforates.
Where a chelant and a filming inhibitor are used together, the order of addition matters, and the compatibility has to be checked in the actual water rather than in demineralised water. An anionic chelant and a cationic inhibitor can form a pair that drops out of solution, which is a problem that shows up as a mysterious deposit a week after the change.
Where to dose and how to control it
The dosing point should be chosen from the pressure profile, not from the drawing of the plant room. In practice three locations cover most schemes.
Downhole or at the wellhead, by capillary string or by intermittent squeeze, is used where the saturation index at the wellhead is already positive and the deposit would otherwise form before the fluid reaches the plant.
At the inlet of the exchanger, on the cold side, is the common compromise. It protects the hottest surfaces and keeps the dose in a stream that is easy to sample.
Before reinjection covers the disposal well, which has its own scaling risk because the fluid is being re-pressurised and cooled on the way down.
Control is by the saturation index, calculated from calcium, alkalinity, pH, temperature and total dissolved solids at each point, not by a single hardness reading. A plant that controls on total hardness alone will over-dose in winter and under-dose in summer, because the saturation index moves with temperature even when the water does not change.
Reinjection wells and the permeability you cannot see
A reinjection well loses injectivity for reasons that are only partly chemical. Suspended particles, bacterial growth, gas binding and clay swelling all compete with scale as explanations, and a chelant programme aimed at the wrong one will not restore the well.
The diagnostic that pays is a step-rate injectivity test combined with a filterable solids measurement on the injected fluid. If injectivity falls while solids stay low and the water is at or below saturation, the problem is mechanical or biological, and the chemical answer is a filtration or a biocide decision rather than a chelant dose.
Where the deposit is confirmed as carbonate, an intermittent chelant treatment at low concentration is usually preferable to a continuous high dose, because the well spends most of its time at conditions where the deposit is stable and only passes through the scaling window during start-up and shutdown.
Compliance in European geothermal projects
Geothermal schemes sit at the junction of several regulatory frameworks, and the documentation set is wider than for a conventional industrial cooling system.
The water framework directive shapes what can be discharged and what has to be reinjected. National mining or geothermal legislation governs the subsurface part and usually requires the composition of any injected fluid to be declared. REACH applies to the chelating agent as a substance, and the registration number for the tonnage band should be supplied with the first delivery. If a biocide is part of the programme, the biocidal products regulation applies to that component separately.
For a scheme that markets its heat as green, the biodegradability documentation is not only a compliance item. Operators increasingly ask for it because the fluid that returns to the aquifer is part of the environmental case they present to the permitting authority.
What to put in the tender
A tender that says "scale inhibitor, biodegradable" will produce offers that cannot be compared. Six items fix most of the ambiguity.
State the water analysis at the dosing point, including temperature, pH, calcium, alkalinity, sulphate, silica, chloride and total dissolved solids. State the target saturation index and the calculation method. State the maximum dose the permit allows. State the materials of construction the product will contact, including elastomers. State the temperature and residence time at the hottest point. And state which documentation will be required at delivery.
Ask each bidder for the calcium capacity per kilogram of product at the operating pH, the thermal stability data at the loop temperature, and a reference plant with a comparable water chemistry. A supplier who cannot name a reference at similar salinity is offering a laboratory product.
Frequently asked questions
Can a chelating agent replace a phosphonate programme entirely?
In many low to moderate temperature loops it can, and the driver is usually the discharge or reinjection permit rather than performance. In high temperature or high salinity loops a blend is often more practical, and the decision should come from the saturation index and the thermal data rather than from a general preference.
Will it remove existing scale in the network? It will dissolve carbonate scale slowly at operating temperature, but a network with years of deposit is usually cleaned mechanically or by a dedicated chemical clean, then kept clean by continuous dosing. Continuous low dosing as a removal strategy is slow and can release particles into customer installations.
Does it work on silica? Not at neutral pH. Silica is controlled by dilution, temperature and pH management, and no chelating agent will dissolve a polymerised silica layer under loop conditions.
How is the dose adjusted through the year? By recalculating the saturation index at the actual loop temperature. The required dose typically rises in winter, when the return temperature is lower and the exchanger works harder, and falls in summer.
What documents should accompany delivery? A batch certificate of analysis, the safety data sheet in the language of the site, the REACH registration confirmation and the OECD 301 biodegradation report.
For a specification sheet, a sample for a loop trial or a review of your water analysis against a proposed dose, write to [email protected] or call +86-537-3739818. Product details are listed at yuanlianchem.com.
Yuanlian Chemical specializes in the production of polyaspartic acid (PASP),tetrasodium iminodisuccinate(IDS), GLDA, MGDA etc. with stable quality and excellent quantity!
Contact us