GLDA-Na4 for Matrix Acidising: A Field Buyer's Guide
A stimulation job is a compromise between how much damage you can remove and how much new damage you are willing to create. Hydrochloric acid removes near-wellbore carbonate quickly, then leaves the formation to deal with spent liquor at a pH that no longer holds iron or calcium in solution. That second half of the job is where chelating acids earned their place, and where the purchasing decision actually matters.
This guide is written for the people who write the specification and sign the purchase order, not for the laboratory that publishes the core-flood data. GLDA-Na4 is the product discussed throughout, because it is the aminopolycarboxylate most often compared with HCl and mud acid in sandstone and carbonate work.
Why operators moved away from plain hydrochloric acid
Hydrochloric acid is cheap, fast and well understood. It is also aggressive to tubulars, particularly at the temperatures found in deeper wells, and it spends itself within centimetres of the perforation in a carbonate. In a sandstone it can disintegrate the clays that hold the matrix together, which converts a permeability problem into a fines migration problem.
The spent acid is the quieter issue. As the liquor is consumed, pH climbs and the dissolved load has to go somewhere. Ferric hydroxide begins to precipitate well below neutral pH, and calcium can follow once the sulphate or carbonate balance tips. The result is a permeability decline that looks like the job failed when in fact the chemistry was never going to hold.
A chelating acid changes that arithmetic. Instead of relying on low pH alone to keep metals dissolved, it supplies a ligand that holds them across a much wider pH range. The acid still dissolves the damage; the ligand keeps the products in the flow stream long enough to be produced back.
What a chelating acid actually does in the pore
Three things happen at once, and it helps to keep them separate when you read a supplier claim.
The first is proton attack on carbonate or on the cementing material between grains. This is normal acid chemistry and it is fast where the mineral is reactive.
The second is complexation. The ligand binds calcium, magnesium and iron, lowering the free ion activity and therefore the saturation state of the mineral. Dissolution can continue at a pH where it would otherwise stop, because the reaction product is being removed from solution rather than accumulating.
The third is retardation. Because the driving force for dissolution falls as the ligand loads up, the reaction front moves more slowly through the rock. In a matrix treatment that is usually an advantage: the treating fluid travels further before it is spent, so the damaged zone is contacted rather than the first few centimetres in front of the perforations.
A product that only does the first is an acid. A product that does the second and third as well is a chelating acid, and the difference shows up in return permeability data rather than in titration figures.
Where GLDA-Na4 fits: carbonate versus sandstone
In carbonate, GLDA is normally blended with hydrochloric acid at a modest ratio, or used as a fully formulated retarded acid. The chelant carries the calcium that the acid liberates and delays the point at which the reaction stalls, so the treating interval is contacted more evenly. Wormholing still occurs, but the competing effect of the ligand tends to widen the invaded zone rather than punch a single dominant channel.
In sandstone, the case is different and often stronger. The concern there is not only removing carbonate cement but doing so without mobilising clays or precipitating aluminium and iron hydroxides. A chelant-based fluid dissolves the carbonate fraction while keeping the released cations complexed, and its near-neutral formulation is much less likely to trigger the clay swelling that conventional mud acid can cause.
Sandstone work does not remove the need for a proper preflush and a clear understanding of the clay type. A chelating acid is more forgiving than HCl, not forgiving of a formation that was never characterised.
The pH path decides the outcome
Every chelating acid job follows a pH trajectory, and the useful question is what the fluid can still hold at each point along it.
At pH below about 2, the ligand is largely protonated and the system behaves like an acid with a mild buffer attached. Calcium capacity is limited by acidity rather than by the chelant, and iron is kept in solution mainly because of the low pH.
Between pH 3 and 6, the ligand becomes the dominant mechanism. This is the window where GLDA does work that HCl cannot: it holds ferric iron and calcium at a point where both would otherwise precipitate as hydroxides or carbonates. Most of the reported advantage of chelating acids over spent HCl sits here.
Above pH 7, the free calcium that is not complexed will find carbonate or sulphate, and the ligand's capacity is finite. A job that over-runs and consumes far more carbonate than designed can therefore end in supersaturation even with a chelant present.
The practical consequence is that the loading ratio of chelant to dissolvable mineral has to be calculated, not assumed. Ask the supplier for the calcium capacity per cubic metre at the pH you will actually see, and check whether that figure is quoted for the neat product or for the diluted field fluid. Figures quoted per kilogram of active are comparable; figures quoted per litre of product are not.
Iron control is where jobs fail quietly
Iron deserves its own heading because it is the most common cause of a disappointing result that gets attributed to the formation.
Ferrous iron is comparatively well behaved. Ferric iron is not: it hydrolyses and forms colloidal hydroxide at low pH, and those particles are exactly the right size to plug pore throats. A small amount of ferric iron, mobilised from tubulars or from an iron-rich mineral, can do more damage than the carbonate the job set out to remove.
Three controls matter. The fluid should be oxygen-free, because oxygen converts ferrous to ferric. The chelant loading should be set with the expected iron in mind, not only the calcium. And the returning fluid should be monitored from the first hour, because a colour change or a sudden turbidity spike tells you the iron has come out of solution while there is still time to adjust the overflush.
GLDA holds ferric iron over a wider pH band than EDTA does at the same molar loading, which is part of why it appears in high-iron sandstone programmes. It does not hold unlimited iron. A well that produces from an iron-rich interval needs a loading figure for that iron, quoted in the same units as the calcium capacity.
Temperature, contact time and corrosion
Two temperature questions need answering before a job is designed, and they are often confused.
The first is thermal stability of the molecule. Aminopolycarboxylates degrade at high temperature by different routes and at different rates, and the rate roughly doubles for every ten degrees until a mechanism changes. GLDA is generally reported as usable in the range where conventional chelating acids operate, but above roughly 150 °C the residence time has to be justified rather than assumed. If your well is hotter than that, ask for degradation data at your temperature and for the half-life you can live with.
The second is corrosion of the tubulars. A neutral chelating acid is far less aggressive than 15 per cent HCl, which is one of its commercial arguments. As soon as it is blended with acid to speed up the reaction, the corrosion question returns and a properly selected inhibitor is needed. Corrosion coupons run at bottomhole temperature with the actual blend are the only figures worth quoting in a job design.
Contact time is the third variable. Retardation is helpful up to the point where the fluid is still in the well when the job is supposed to be over. A chelating acid that stays in the formation for days is a workover risk, not a benefit.
What to specify when you order
The specification should be written so that two suppliers quoting the same product can be compared line by line.
State the active content and the counter-ion. Tetrasodium and tripotassium salts behave differently on dilution and on clay stability, and the price per tonne is meaningless without knowing which one is being quoted. State the pH of the delivered solution and the density, because both affect how the field blend is calculated.
Ask for the calcium capacity in millimoles of calcium per kilogram of product at a stated pH, and separately for the iron capacity. Ask for the chloride and sulphate levels, which matter in a formation with sensitive clays. Ask for the thermal stability data at your bottomhole temperature and the analytical method used to generate it.
On the compliance side, a REACH registration number for the tonnage band you are buying and a biodegradation report to OECD 301 are the two documents a European operator will want to file. Offshore work may bring additional requirements from the regional convention that applies to the area.
Running a pilot without shutting the well
A field trial does not need a full core-flood programme to be informative. What it needs is a before-and-after that the production engineer will accept.
Record the injection pressure at a fixed rate before the job, and again during the overflush. Sample the returns on a schedule, not when someone remembers, and analyse for calcium, total iron, ferrous iron, pH and turbidity. A return sample that stays clear is worth more than a headline permeability number, because it shows the metals never came out of solution.
Keep one interval untreated if the field allows it. The comparison between treated and untreated wells in the same reservoir says more about the fluid than any single-well result, and it survives the scrutiny that a vendor-supplied case study does not.
Frequently asked questions
Can GLDA replace hydrochloric acid completely? In some carbonate and sandstone treatments, yes. In others it is blended, because the job needs a faster reaction than a pure chelating acid provides. The choice depends on the damage type and on how much time the operation can spend.
How much chelant is needed per metre of interval? There is no universal figure. It is calculated from the dissolvable mineral volume, the expected iron load and the calcium capacity of the product at the pH the fluid will reach. Any supplier quoting a fixed rate without your water and core data is guessing.
Does a biodegradable chelant perform as well as EDTA? For calcium and ferric iron in the pH band where GLDA is active, performance is comparable at equal molar loading. The practical advantage is the end-of-life behaviour in the returns and in the disposal route.
Will it damage the formation if the job over-runs? The risk is supersaturation once the ligand is loaded, particularly for calcium if carbonate is still available. Design the overflush to displace the spent fluid rather than leave it resident.
What documentation should come with the first delivery? A batch certificate of analysis with the calcium capacity figure, the safety data sheet in the site language, the OECD 301 report and the REACH registration confirmation.
For a specification sheet, a sample for a core-flood or a review of your water and core data against a proposed loading, write to [email protected] or call +86-537-3739818. Product details are listed at yuanlianchem.com.
Yuanlian Chemical specializes in the production of polyaspartic acid (PASP),tetrasodium iminodisuccinate(IDS), GLDA, MGDA etc. with stable quality and excellent quantity!
Contact us